Question 1

How much does a concrete driveway cost in Sherman?

Accepted Answer

Published national cost guides put plain gray concrete at roughly $4 to $8 per square foot installed, with decorative finishes above that, so a typical two-car replacement lands in the mid four figures to low five figures. The honest number comes from a free on-site walkthrough with a written fixed price. Driveway pricing is set by more than square footage, which is why a per-foot number quoted over the phone is a guess. Five factors move a Sherman quote. Tear-out: sawing, breaking, and hauling off an old slab costs real money that a pour over prepared ground does not. Base work: on Blackland clay east and south of town, moisture conditioning and 4 to 6 inches of compacted flex base are what keep the new driveway flat, and they are a meaningful share of the price; on sandy ground west of US 75 the base scope is lighter. Thickness and steel: a 4-inch car driveway and a 6-inch section that carries a loaded trailer are different quantities of concrete and rebar. The road end: a culvert set or replaced, a TxDOT-geometry approach on a highway, or a tie-in to a city sidewalk each add defined line items. Finish: broom-finish gray prices below stamped or decorative work. The way to compare bids is to compare scopes, not totals: a lower number that says nothing about base depth, reinforcement, joint layout, or haul-off is not a lower price for the same driveway. Every estimate here is written, itemized, and fixed before work begins, and the estimate itself is free.

Question 2

How thick should a concrete driveway be?

Accepted Answer

Four inches is the standard for cars and pickups on a properly compacted base. Go to 5 or 6 inches wherever heavier loads live: trailers, RVs, equipment, and the approach and gate areas they cross. Concrete strength of 3,000 to 4,000 psi is the common spec here. Thickness follows the heaviest regular load, not the average one. A 4-inch slab over 4 to 6 inches of compacted base handles daily cars and pickups for decades. The places that deserve 5 to 6 inches are predictable: the apron where a gooseneck or camper swings in, the pad where a boat or tractor parks, the run to a shop door, and rural entrances that will someday see a concrete truck, a hay trailer, or a propane delivery. Thickening those areas at pour time costs a fraction of repairing a cracked 4-inch section later. Two companion specs matter as much as thickness. First, the base: thickness cannot rescue a slab poured on loose or wet-soft clay, which is why subgrade compaction and base depth appear as line items in every written scope here. Second, the joints: control joints belong at roughly 8 to 12 feet each way on a 4-inch slab (the working rule is 2 to 3 times the thickness, expressed in feet), cut to a quarter of the slab depth, so shrinkage cracks form inside the joints instead of across the surface. Concrete in the 3,000 to 4,000 psi range, reinforced and jointed correctly over a real base, is what a North Texas driveway spec should say. If a bid lists thickness alone, the important half of the spec is missing.

Question 3

Does a concrete driveway need rebar?

Accepted Answer

On North Texas clay, yes: reinforcement earns its cost. The common spec is #3 rebar on 18 to 24 inch centers, supported on chairs so the steel sits mid-slab. Steel does not prevent cracks; it holds them tight so the slab keeps acting like one piece. Concrete cracks; that is not a defect, it is a material property. Reinforcement exists to control what happens next. Unreinforced slabs on expansive clay crack, then the cracks widen, offset in height, and let water into the base, and the failure compounds. Reinforced slabs crack hairline inside the control joints and stay locked together, which is the difference between a driveway that ages and one that breaks up. The spec details matter more than the buzzwords. Bar (#3, sometimes #4 at heavy sections) on 18 to 24 inch centers is the standard here. Placement decides whether you got what you paid for: steel lying on the dirt does nothing, so it goes on chairs or gets pulled to mid-slab during the pour. Welded wire mesh can work when it is engineered sheet mesh properly supported, but mesh trampled to the bottom of the pour is the classic corner cut. Fiber additives improve surface characteristics and help with plastic shrinkage, but fiber alone is not structural reinforcement for clay-country driveways. One more honesty check: reinforcement is the second line of defense. The first is the base. A reinforced slab over uncompacted fill still settles; the steel just holds the broken pieces politely together. The written scope here states bar size, spacing, and support, and the base preparation above it, so both defenses are on paper.

Question 4

How long before you can drive on new concrete?

Accepted Answer

Walk on it after 24 to 48 hours, drive cars on it after about 7 days, and keep heavy trucks off for the full 28-day cure. Concrete reaches roughly 70 percent of its design strength in the first week and its rated strength at 28 days. Concrete does not dry; it cures, a chemical reaction that needs time and moisture. The strength curve is steep early and long afterward: roughly 70 percent of design strength arrives in about 7 days, and the 3,000 to 4,000 psi the mix is rated for is a 28-day number. The practical schedule follows that curve. Foot traffic is fine at 24 to 48 hours. Passenger vehicles wait about 7 days. Concrete trucks, moving vans, loaded trailers, and equipment wait the full 28, and on a rural drive it is worth scheduling deliveries around that window. Cure quality is set in the first week, which is why the scope states the method: curing compound sprayed at finish, or wet curing, either of which slows moisture loss so the surface gains hardness instead of dusting. Texas summer makes this real: a slab poured at 100 degrees and left bare can lose water faster than the reaction can use it, which is why summer pours start at first light and cure protection is not optional. Two first-year rules protect the investment: keep deicing salts off the slab its first winter (the surface is still maturing and salt scaling is permanent), and keep skid-steer turns and trailer jack points off the edges. After that, a correctly built slab does not ask for much for a very long time.

Question 5

Do I need a permit for a driveway in Sherman?

Accepted Answer

Inside Sherman city limits, driveway and approach work runs through the city's Self Service Portal, and contractors register with the city. An approach onto a state highway needs a TxDOT access permit. On unincorporated county land there is no residential building permit, but county road rules still govern culverts. Who permits your driveway depends on where the driveway meets the road. Inside Sherman, the city's Development Services department handles driveway, approach, and sidewalk work through its online Self Service Portal, the same system that handles building permits and contractor registration; Denison, McKinney, Anna, Melissa, and the other corridor cities run equivalents. Where the driveway connects to a state-maintained highway (US 75 frontage, US 82, US 69, US 377, SH 289, and the FM roads), the approach itself needs a TxDOT access permit regardless of city or county, and TxDOT's Access Management Manual sets the geometry: a residential driveway meets the road at 75 to 90 degrees, tops out at 24 feet wide, carries minimum 15-foot radii, uses an all-weather surface, and cannot dump drainage onto the highway. On unincorporated Grayson, Cooke, Fannin, and Bryan county land, Texas and Oklahoma counties generally do not issue residential building permits, so the driveway itself needs none, but the county road department still governs the culvert and approach where you tie into a county road, and floodplain rules apply where mapped. The practical takeaway: the permit question is answered by the road authority, not the concrete. The written scope here names which authority applies to your address and who pulls what, so none of it surfaces mid-project.

Concrete Driveways, Roads & Sidewalks in Collinsville, TX

Veterans, Seniors, and First Responders Discount

Concrete Driveways, Roads & Sidewalks in Collinsville

Concrete Driveways, Roads & Sidewalks in Collinsville: US 377 ranch country between Whitesboro and Pilot Point and Grayson County ground conditions

Ready to get started in Sherman?

Concrete Driveways, Roads & Sidewalks in Collinsville, TX

North Texas Construction Pros trust signals

Veterans, Seniors, and First Responders Discount

Concrete Driveways, Roads & Sidewalks in Collinsville

Concrete Driveways, Roads & Sidewalks in Collinsville: US 377 ranch country between Whitesboro and Pilot Point and Grayson County ground conditions

Ready to get started in Sherman?